• Sound Level Meters
  • Rion NA-28 (Class 1)
  • Rion NL-32 (Class 1)
  • Rion NL-31 (Class 1)
  • Rion NL-22 (Class 2)
  • Rion NL-21 (Class 2)
  • Rion NL-20 (Class 2)
  • NL Series Options
• Vibration Meters
  • Rion VA-11 Vibration Analyser
  • Rion VM-53 & 53A Vibration Meter
  • Rion VM-82 Vibration Meter
• Vibration & Frequency Analyzers
  • Rion SA-78 2 Channel Frequency Analyser
• Vibration Switches
  • FFE Type 3161MR
• Condition Monitoring
  • Rion VA-11C Vibration Analyser with Data Logger
• Viscotesters
  • Rion VT-03F Viscometer
  • Rion VT-04F Viscometer
• Heat Stress & Indoor Air Quality
  • Aim RSS-214 Heat Stress Monitor
• Gas Monitoring & Detectors
  • Aim Commander - Portable Multi-Gas Detector
  • IST-Aim Logic 915 Stand Alone Gas Detector
• Calibrators
  • Rion NC-72 Pistonphone
  • Rion NC-74 Acoustic Calibrator
  • Rion VE-10 Vibration Calibrator
• Environmental Chambers
  • Angelantoni Environmental Test Chambers
• Transducers
  • Rion PV Series of Accelerometers
  • Rion UC-/UH-Series - Condenser Microphones
• Data Recorders
  • Rion DA-20

Rion VA-11C Vibration Analyser with Data Logger

Specifications below as per standard Rion VA-11, but in addition the VA-11C has a data collection function used to gather measurement data at multiple diagnostic points along a pre-determined route. The ProConn11C Condition Monitoring and Analysis software is then used to build-up an equipment database for maintenance purposes.

• For examining machinery vibrations and performing diagnostic routines on various kinds of equipment
• Vibration meter mode and analyzer mode encompassing FFT analysis
• Simultaneous display of acceleration, velocity and displacement
• 80 dB dynamic range with 16-bit A/D converter
• Large LCD panel with EL backlight
• Operates for more than 22 hours on four IEC R14 (alkaline) batteries

View more product details Download PDF

Specifications
Input section
Input connector	Connector for standard accelerometer (PV-57)
Measurement range	Acceleration: 0.02 to 316m/s2 RMS Velocity: 0.1 to 1000mm/s RMS Displacement: 0.003 to 28.3mm (EQ p-p)
Filter	High-pass filter: 3Hz, 10Hz, 1kHz (-10% frequency) Low-pass filter: 1kHz, 5kHz, 20kHz (-10% frequency)
Input section - Vibration meter mode
Processing items	Simultaneous processing of following items (digital) Acceleration: rms, peak, crest factor Velocity: rms Displacement: Equivalent P-P value (EQ p-p)
Input section - Analyzer mode
A/D Converter	16-bit, delta sigma principle, 51.2 kHz sampling
Processing items	Waveform, spectrum
Display range	80 dB
Trigger operation	Free-run, repeat, single
Pre and post trigger function	Yes
Display section
Display	EL backlit LCD, 192 X 128 dot, 77.5 X 54 mm
Vibration meter display data	Acceleration Velocity Displacement
Spectrum display	Graph; List
Graph display	102 lines (frequency spectrum 101 lines + overall value) Y axis (dB, linear)
List display	Upper 10 levels and frequency
Waveform display	Graph only, 128 data
Memory
Data memory	Manual store: up to 500 data sets Transient store: Continuous store of waveform (sore cycle: frequency span X 2.56)
Re-analyze function	Data stored in transient memory can be re-analyzed
Measurement settings memory	10 sets
PCMCIA Card	ATA type compact flash. Contents of entire data memory are written to the card as one ASCII file in MS-DOS format